Search Results

Standard

15 Pole Connector Between Towing Vehicles and Trailers with 12 Volt Nominal Supply

2020-02-25

CURRENT

J2691_202002

This SAE Standard establishes the minimum construction and performance requirements for a 15 pole connector between towing vehicles and trailers, for trucks, trailers, and dollies, for 12 VDC nominal applications in conjunction with SAE J2742. The connector accommodates both power and ISO 11992-1 signal circuits along with dual ground wires to accommodate grounding requirements within the constraints of the SAE J2691 terminal capacity.

Standard

Overhead Protection for Agricultural Tractors - Test Procedures and Performance Requirements

2020-02-20

CURRENT

J167_202002

This SAE Standard applies to an overhead cover installed on a protective frame or enclosure conforming to SAE J2194 or alternately SAE J1194 and the following additional requirement of a drop test to verify the effectiveness of the overhead cover in protecting the operator from falling objects. The test procedures and performance requirements outlined in this document are based on currently available engineering data.

Standard

Cab Roof Strength Evaluation - Quasi-Static Loading Heavy Trucks

2020-01-21

WIP

J2422

This SAE Recommended Practice describes the test procedures for conducting quasi-static cab roof strength tests for heavy-truck applications. Its purpose is to establish recommended test procedures which will standardize the procedure for heavy trucks. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.

Standard

Flashing Warning Lamp for Industrial Equipment

2019-12-09

CURRENT

J96_201912

This SAE Standard covers the general requirements and the test requirements for a flashing warning lamp for industrial wheeled equipment.

Standard

Heavy-Duty Wiring Systems for On-Highway Trucks

2019-12-03

HISTORICAL

J2202_201912

This SAE Recommended Practice provides general guidelines on the material selection, construction, and qualification of components and wiring systems used to construct nominal 12 VDC and/or 24 VDC electrical wiring systems for heavy-duty vehicles The guidelines are limited to nominal 12 VDC and/or 24 VDC primary wiring systems and includes cable sizes American Wire Gage 20 to AWG 4 on heavy-duty on-highway trucks. The document identifies appropriate operating performances requirements. This document excludes the male-to-female connection of the SAE J560 connectors.

Standard

Three-Point Hitch (Type A) Backhoe Personnel Protection

2019-08-28

CURRENT

J1518_201908

This SAE Recommended Practice applies to three-point hitch (Type A) backhoes as defined in SAE J326 when mounted on either an agricultural tractor as defined in ANSI/ASAE S390 or other off-road self-propelled work machine as defined in SAE J1116. This criterion is intended for the manufacturer of the backhoe, whether or not the backhoe is manufactured or marketed by the same company that manufactures or markets the propelling machine.

Standard

Off-Road Rim Maintenance Procedures and Service Precautions Diameter Code 20 and Larger

2019-02-21

CURRENT

J1337_201902

This SAE Recommended Practice covers the important fundamental maintenance and service precautions for all off-road single-piece and multi-piece rims. Detailed information on specific procedures concerning mounting, demounting, maintenance, and service of a particular type, style, or design of off-road rim assembly can be obtained by consulting rim or tire manufacturers or distributors. These procedures and service precautions should be considered in preparation of the machine service manual, the operator's manual, and workplace procedures.

Standard

Physical Layer, 250 Kbps, Un-Shielded Twisted Pair (UTP)

2018-12-14

CURRENT

J1939/15_201812

This document describes a physical layer utilizing Unshielded Twisted Pair (UTP) cable with extended stub lengths for flexibility in ECU placement and network topology. Also, connectors are not specified. CAN controllers used on SAE J1939-15 networks must be restricted to use only Classical Frames as defined in ISO 11898- 1. A network which may have legacy controllers cannot tolerate FD Frames. These SAE Recommended Practices are intended for light- and heavy-duty vehicles on- or off-road as well as appropriate stationary applications which use vehicle derived components (e.g., generator sets). Vehicles of interest include, but are not limited to: on- and off-highway trucks and their trailers; construction equipment; and agricultural equipment and implements.

Standard

Nomenclature - Hydraulic Backhoes

2018-11-20

HISTORICAL

J326_201811

This SAE standard includes hydraulic backhoes which have no more than 190 degrees of rotational swing and are mounted on wheeled tractors and crawler tractors. Illustrations used are not intended to include all existing commercial machines or to be exact descriptions of any particular machine. The illustrations have been chosen to describe the principles to be used in applying this standard.

Standard

Trailer Grade Parking Performance Test Procedure

2018-11-12

CURRENT

J1452_201811

This SAE Recommended Practice establishes methods to determine grade parking performance with respect to: a Ability of the parking brake system to lock the braked wheels. b The trailer holding or sliding on the grade, fully loaded, or unloaded. c Applied manual effort. d Unburnished or burnished brake lining friction conditions. e Down and upgrade directions.

Standard

Data Link Layer

2018-10-03

HISTORICAL

J1939/21_201810

The SAE J1939 documents are intended for light, medium, and heavy-duty vehicles used on or off road, as well as appropriate stationary applications which use vehicle derived components (e.g., generator sets). Vehicles of interest include, but are not limited to, on- and off-highway trucks and their trailers, construction equipment, and agricultural equipment and implements. The purpose of these documents is to provide an open interconnect system for electronic systems. It is the intention of these documents to allow Electronic Control Units to communicate with each other by providing a standard architecture. This particular document, SAE J1939-21, describes the data link layer using the Classical Extended Frame Format (CEFF) with 29-bit IDs, as defined in ISO 11898-1, December 2015. For SAE J1939, no alternative data link layers are permitted.

Standard

Nomenclature - Clam Bunk Skidder

2018-09-02

HISTORICAL

J1353_201809

This SAE Recommended Practice identifies major components and parts peculiar to clam bunk skidders. Illustrations used here are not intended to include all existing machines or to be exactly descriptive of any particular machine. They have been provided to illustrate the principles to be used in applying this document.

Standard

Component Nomenclature - Skidder - Grapple

2018-09-02

HISTORICAL

J1111_201809

This SAE Standard characterizes grapple skidders and identifies the major components and parts most commonly associated therewith. Illustrations used herein are not intended to include all existing commercial machines or to be exactly descriptive of any particular machine. They have been included to facilitate application of this document

Standard

Truck and Bus Lane Departure Warning Systems Test Procedure and Minimum Performance Requirements

2018-08-28

CURRENT

J3045_201808

This SAE Recommended Practice establishes a uniform, powered vehicle test procedure and minimum performance requirement for lane departure warning systems used in highway trucks and buses greater than 4546 kg (10000 pounds) GVW. Systems similar in function but different in scope and complexity, including Lane Keeping/Lane Assist and Merge Assist, are not included in this document. This document does not apply to trailers, dollies, etc. This document does not intend to exclude any particular system or sensor technology. The specification will test the functionality of the LDWS (e.g., ability to detect lane presence, and ability to detect an unintended lane departure), its ability to indicate LDWS engagement, its ability to indicate LDWS disengagement, and determine the point at which the LDWS notifies the Human Machine Interface (HMI) or vehicle control system that a lane departure event is detected.

Standard

Motorcycle Auxiliary Front Lamps

2018-08-13

CURRENT

J1306_201808

This engineering design specification provides parameters and general requirements for auxiliary front lamps to be used on motorcycles.

Standard

15 Pole Connector Between Towing Vehicles and Trailers with 12 Volt Nominal Supply

2018-04-15

HISTORICAL

J2691_201804

This SAE standard establishes the minimum construction and performance requirements for a 15 Pole Connector Between Towing Vehicles and Trailers, for trucks, trailers, and dollies in conjunction with SAE J2742. The connector accommodates both power and ISO 11992-1 signal circuits along with dual ground wires to accommodate grounding requirements within the constraints of the SAE J2691 terminal capacity.

Standard

High Tension Ignition Cable Assemblies - Marine

2018-02-24

CURRENT

J1191_201802

This Standard covers the requirements for all marine inboard and outboard gasoline engine ignition assemblies and components.

Standard

Lighting Identification Code

2017-12-20

CURRENT

J759_201712

This SAE Recommended Practice provides the lighting function identification codes for use on all passenger vehicles, trucks, trailers, motorcycles, and emergency vehicles.

Standard

Headlamps for Industrial Equipment

2017-10-10

CURRENT

J95_201710

This SAE Standard provides performance and general design requirements and related test procedures for headlamps for use on industrial wheeled equipment that may be operated on public roads.

Standard

Cast Shot and Grit Size Specifications for Peening and Cleaning

2017-10-10

HISTORICAL

J444_201710

This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches1, preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E 11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.